Product ID:METACERAM 21021 THERMAL SPRAY POWDER
MSDS Date:12/27/1994
FSC:3439
NIIN:01-191-5053
MSDS Number: CGMJT

EUTECTIC CORP

40-40 172ND STREET
FLUSHING, NY 11358-9981
US

Emergency Phone: 718-358-4000

Info Phone: 718-445-1784

Cage: 72271

EUTECTIC CORP

CHARLOTTE, NC 28273 US

Telephone: 704-527-9800/ 800-221-1433

Cage: 72271

NICKEL (SARA 313) (CERCLA)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 85-95%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3; 9596

ALUMINUM (SARA 313)

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: 3-8%

OSHA PEL 15 MG/M3 DUST

ACGIH TLV: 10 MG/M3 DUST; 9596

MOLYBDENUM

CAS: 7439-98-7

RTECS: QA4680000

OSHA PEL 10 PPM.

ACGIH TLV: 10 PPM.

LD50 LC50 Mixture:TLV WELDING FUMES/DUSTS: 5 MG/M3
Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:LITTLE OR NO HAZARDS EXIST FOR PRODUCT
UNTIL IT IS USED IN THE WELDING PROCESS. INHALATION OF WELDING
FUMES CAN BE DANGEROUS TO HEALTH AND MAY CAUSE LUNG DAMAGE OR OTHER
ORGAN DAMAGE. INHALATION MAY C AUSE ALLERGIC RESPIRATORY REACTION.
EYE/SKIN CONTACT CAN INJURE EYES AND BURN SKIN. MAY BE HARMFUL OR
FATAL IF SWALLOWED
Explanation of Carcinogenicity:THIS COMPOUND CONTAINS NICKEL CONSIDERED
CARCINOGENIC BY IARC AND NTP.
Effects of Overexposure:EYE IRRITATION/BURNS, SKIN IRRITATION/BURNS,
NOSE/THROAT IRRITATION, WEIGHT LOSS, DIGESTIVE DISTURBANCES,
METALLIC TASTE, NAUSEA, TIGHTNESS OF CHEST, FEVER, ALLERGIC
REACTIONS, LUNG FIBROSIS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYES: FLUSH WITH WATER FOR 15 MINUTES WHILE HOLDING EYELIDS
OPEN. GET MEDICAL ATTENTION. SKIN: REMOVE CONTAMINATED CLOTHING.
WASH WITH SOAP AND WATER. IF IRRITATION PERSIST, GET MEDICAL
ATTENTION. INH ALATION: REMOVE TO FRESH AIR. RESTORE BREATHING. GET
MEDICAL ATTENTION. INGESTION: CALL PHYSICIAN OR POISON CONTROL
CENTER. ADVISE OF INGREDIENTS.

Flash Point:NONFLAMMABLE
Lower Limits:NOT GIVEN
Upper Limits:NOT GIVEN
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD WEAR SELF CONTAINED
BREATHING APPARATUS AND FULL PROTECTIVE GEAR. TOXIC FUMES MAY BE
PRODUCED.
Unusual Fire/Explosion Hazard:METAL POWDER DUST MAY PRESENT A FIRE OR
EXPLOSION HAZARD UNDER FAVORABLE CONDITIONS OF PARTICLE SIZE,
DISPERSION AND STRONG IGNITION SOURCE.

Spill Release Procedures:CONTAIN SPILL, ABSORB AND SWEEP UP. FLUSH AREA
WITH WATER TO AN APPROVED CHEMICAL DRAIN. DISPOSE OF IN AN
ENVIRONMENTALLY SENSITIVE MANNER IN ACCORDANCE WITH FEDERAL, STATE
AND LOCAL REGULATIONS. USE APPROPRIATE MEASURES TO CONTROL
AIRBORNE DUST.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY
FROM THE FUME/DUST PLUME.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

Respiratory Protection:IF THE SORK STATION IS NOT PROPERLY VENTILATED
TO EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW THE RECOMMENDED
EXPOSURE LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:EXHAUST VENTILATION SUFFICIENT TO KEEP AIRBORNE
CONCENTRATIONS BELOW RESPECTIVE TLV'S.
Protective Gloves:CHEMICAL & OIL IMPERVIOUS GLOVES
Eye Protection:CHEMICAL TIGHT GOGGLES. FACE SHIELD
Other Protective Equipment:CHEMICAL RESISTANT CLOTHING AS NECESSARY TO
PREVENT SKIN CONTACT. AN EMERGENCY EYEWASH AND SHOWER SHOULD BE
AVAILABLE.
Work Hygienic Practices:WASH HANDS THOROUGHLY WITH SOAP AND WATER
BEFORE EATING, DRINKING, SMOKING OR USING TOILET FACILITIES.
Supplemental Safety and Health
THE PRIMARY ROUTE OF ENTRY OF WELDING FUMES, GASES AND DUST IS BY
INHALATION. SKIN, EYE CONTACT AND INGESTION MAY ALSO OCCUR WITH
POWDERS, PASTES AND LIQUIDS. IT IS RECOMMENDED TO MONITOR FOR ALL
INGR EDIENTS IN A PARTICULAR PRODUCT AND DECOMPOSITION PRODUCTS
THAT HAVE EXPOSURE LIMITS BELOW 5 MG/M3.

HCC:N1
Boiling Pt:B.P. Text:NOT GIVEN
Melt/Freeze Pt:M.P/F.P Text:NOT GIVEN
Vapor Pres:NOT GIVEN
Vapor Density:NOT GIVEN
Spec Gravity:NOT GIVEN
Viscosity:NOT GIVEN
Evaporation Rate & Reference:NOT GIVEN
Solubility in Water:NOT GIVEN
Appearance and Odor:NOT GIVEN

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, CYANIDES, SULFIDES
Stability Condition to Avoid:HIGH TEMPERATURES, SPARKS, OPEN FLAMES
Hazardous Decomposition Products:THE COMPOSITION & QUANTITY OF
DECOMPOSITION PRODUCTS ARE DEPENDENT ON THE WELDING PROCESS.

Waste Disposal Methods:PREVENT WASTE FROM CONTAMINATING SURROUNDING
ENVIRONMENT. DISCARD ANY PRODUCT, RESIDUE, DISPOSAL CONTAINER OR
LINER IN ACCORDANCE WITH ALL FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.